Paper Entrance 12 inch LP Inner Sleeves Paper 100 Sheets 55166 Japan Import
Model 55166. PAPER Entrance · Imported from Japan. The instruction manual is in Japanese.
Cartridge Headshll Lead Wire Set With Protective Sleeves Over Clips
One Set Of Four Phonograph / Turntable Cartridge Color Coded Lead Wires in a Sealed Package, from a smoke free environment. *The color code for the majority of turntables and tonearms is: Left = White, Left Ground = Blue, Right = Red, Right Ground = Green *For a removable headshell the typical wiring is as follows, when viewed from the wire side of the headshell connector: Upper Left = White, Upper Right = Red, Lower Left = Blue, Lower Right = Green Check the turntable user guide to confirm the colors above. There may be variations depending on the make and model of the turntable. Installation: Clamp just behind the barrel of the clip onto the flattened, crimped area of the lead, and using tweezers or needle nose pliers for installation, line up the barrel of the clip to the cartridge pin terminal, and carefully slide the barrel onto the pin and slide the sleeve over the pin to keep out dust and dirt from collecting on the pins. Be careful and do not bend the crimped ends.: FEEDBACK: Our goal is to satisfy our customers and earn positive 5 star feedbacks for every item. If you are happy with your purchase, please take a minute to leave us a positive 5 star feedback. If you have any issues with your purchase, please contact us directly using eBay’s message service to resolve the issue so that we can earn your positive 5 star feedback. Thank You Import duties, taxes, and customs charges are not included in the item price or shipping cost. These charges are the buyers responsibility. At your option please check with your country's customs office to determine what these additional costs will be prior to bidding or buying.
5 Cartridge Clips Connectors 4 Sleeves For TONEARM Wire Turntable Record Player
The cartridge with the shrink tube installed on a clip and shown in the gallery photo is for illustration only and is not included in this listing. I find it best to slide the shrink tube over the wire and then solder the wire in the the cup just below the crimp area of the tube with as little solder as possible. Crimp the wire over the insulation on the wire and slide the shrink tube over the clip and heat shrink it onto the clip. Caution: Using too much solder wont allow you to slide the the tube over the clip. You can also shorten the clip if desired by breaking off the crimp portion leaving the cup, and repeating the above. See gallery photo. I am offering from my smoke free home 5 cartridge clips and 4 heat shrink sleeves. Enough for one cartridge with one extra clip. The clips are .587 inches or 1.490 cm long and the contact area of the clips are flashed gold over nickel and have a contact resistance of .01 ohms. All components are RoHS Compliant lead free materials. *Compression type clips will fit all modern round cartridge pins sizes: .050 inches / 1.27 mm nominal, and will also fit round cartridge pins from .0492 inches / 1.20 mm to .0531 inches / 1.35 mm The lengths of shrink tube, Red, White, Blue, and Green, is approximately 13/16 inches or 2.06 cm long. After crimping I use a dab of solder to insure I have a good connection. If you have any questions, please contact me prior to your purchase. FEEDBACK: Our goal is to satisfy our customers and earn positive 5 star feedbacks for every item. If you are happy with your purchase, please take a minute to leave us a positive 5 star feedback. If you have any issues with your purchase, please contact us directly using eBay’s message service to resolve the issue so that we can earn your positive 5 star feedback. Thank You Import duties, taxes, and customs charges are not included in the item price or shipping cost. These charges are the buyers responsibility. At your option please check with your country’s customs office to determine what these additional costs will be prior to bidding or buying.
9 Cartridge Clips Connectors 8 Sleeves For TONEARM Wire Turntable Record Player
The cartridge with the shrink tube installed on a clip and shown in the gallery photo is for illustration only and is not included in this listing. I find it best to slide the shrink tube over the wire and then solder the wire in the the cup just below the crimp area of the tube with as little solder as possible. Crimp the wire over the insulation on the wire and slide the shrink tube over the clip and heat shrink it onto the clip. Caution: Using too much solder wont allow you to slide the the tube over the clip. You can also shorten the clip if desired by breaking off the crimp portion leaving the cup, and repeating the above. See gallery photo. I am offering from my smoke free home nine (9) cartridge clips, and 8 heat shrink sleeves. Enough for two cartridges with one extra clip. The clips are .587 inches or 1.490 cm long and the contact area of the clips are flashed gold over nickel and have a contact resistance of .01 ohms. All components are RoHS Compliant lead free materials. *Compression type clips will fit all modern round cartridge pins sizes: .050 inches / 1.27 mm nominal, and will also fit round cartridge pins from .0492 inches / 1.20 mm to .0531 inches / 1.35 mm The eight (8) lengths of heat shrink tube, (two each of the following colors) Red, White, Blue, and Green, are approximately 13/16 inches or 2.06 cm long. After crimping I use a dab of solder to insure I have a good connection. If you have any questions, please contact me prior to your purchase. FEEDBACK: Our goal is to satisfy our customers and earn positive 5 star feedbacks for every item. If you are happy with your purchase, please take a minute to leave us a positive 5 star feedback. If you have any issues with your purchase, please contact us directly using eBay’s message service to resolve the issue so that we can earn your positive 5 star feedback. Thank You Import duties, taxes, and customs charges are not included in the item price or shipping cost. These charges are the buyers responsibility. At your option please check with your country’s customs office to determine what these additional costs will be prior to bidding or buying.
Cartridge Head Shell Lead Wire Set Of 4 Each 1 5/8 Inches With Sleeves
One Set Of Four Phonograph / Turntable Cartridge Color Coded Lead Wires with clear sleeves from a smoke free environment. *The color code for the majority of turntables and tonearms is: Left = White, Left Ground = Blue, Right = Red, Right Ground = Green *For a removable headshell the typical wiring is as follows, when viewed from the wire side of the headshell connector: Upper Left = White, Upper Right = Red, Lower Left = Blue, Lower Right = Green Check the turntable user guide to confirm the colors above. There may be variations depending on the make and model of the turntable. Installation: Clamp just behind the barrel of the clip onto the flattened, crimped area of the lead, and use tweezers or needle nose pliers for installation. FEEDBACK: Our goal is to satisfy our customers and earn positive 5 star feedbacks for every item. If you are happy with your purchase, please take a minute to leave us a positive 5 star feedback. If you have any issues with your purchase, please contact us directly using eBay’s message service to resolve the issue so that we can earn your positive 5 star feedback. Thank You Import duties, taxes, and customs charges are not included in the item price or shipping cost. These charges are the buyers responsibility. At your option please check with your country's customs office to determine what these additional costs will be prior to bidding or buying.
Turntable Ground Wire | 18 AWG Premium Wire w/ Spade | Paracord Sleeve | Phono
Wrapped in ultra durable, high tensile strength and colorful premium paracord. 18 AWG, aerospace grade, tinned copper stranded wire with a high temperature PVC clad coating, flexible. Ensure aclean, noise-free connection between your turntable and amplifier with thisTurntable Ground Connection Wire.
- « Anterior
- 1
- 2
- 3